Install Instructions for 10-1006

Important Note:

Some suction fittings were made incorrectly and measure at .51" rather than .50". Sandpaper can be used to take some thickness off the fitting or you can call us at 909.675.1313 and we can send you a replacement fitting.

Step 1

Remove the filler hose from the tank or at the hose clamp connecting the hose to the metal filler neck

• Small flathead screwdriver

Step 2

Center up a transmission jack under the tank.

• Installation can be completed without a lift. Make sure the vehicle is safely parked with the parking brake set. If your truck is lowered or has running boards you may have to use a jack to get the S&B Tank in position.

Step 3

Remove the 2 fuel tank straps.

• 15mm socket and extension

Step 4

Lower the tank 3-4 inches and remove the 2 fuel lines that are going from the fuel tank sending unit to the fuel cooler.

• GM fuel line disconnect tool

Step 5 for 10-1006 tank

Remove the electrical connector by sliding out the grey tab and depressing the top bottom.

Step 5 for 10-1023 tank

Remove the electrical connector by releasing the tab on the side and pulling out on the connector.

Step 6 for 10-1006

Remove the hose clamp securing the fuel vent hose to the sending unit barb.

Step 7

Remove the fuel tank from the vehicle and transfer over the feed and return line onto the S&B Tank. Be sure the fuel line connectors are clean before connecting to the S&B sending unit.

Step 7b

Place the S&B o'ring into the o'ring groove. Then when the bucket is already in the tank, install the float onto the bucket.

Step 8

Center the hydraulic jack underneath the fuel tank and raise until you can make the connection with the electrical connector(Step 9) and then raise the tank more until you can connect the vent hose onto the sending unit(Step 10) and reconnect the 2 fuel lines onto the fuel cooler(Step 11). Step 10 is for the 10-1006 tank. Once these connections are made, the tank can be lifted all the way into the truck.

• Lift Install: Hydraulic Jack
• Floor Install: Floor jack with added support to properly hold tank

Step 9

Reconnect the electrical connector onto the S&B sending unit. The 10-1023 tank will require the included electrical connector adaptor.

Step 10 for 10-1006

Reconnect the vent hose onto the S&B sending unit. This step is only for the 10-1006 as the 10-1023 tank has the vent inside the fuel fill hose.

• Flat head screwdriver

Step 11

Reconnect the 2 fuel lines coming from the sending unit onto the fuel cooler.

Step 12

Route the 5/16" vent from the from the front part of the tank over the crossmember and onto the barbed fitting.

Step 13

Install the 2 S&B fuel tank straps.

Step 14

Install the S&B support bar in front of the S&B Tank. The hooks should be over the inside lip of the frame rail. Then by pressing up on the tank and pushing on the bar, slide the bar under the S&B Tank until it is in the groove on the S&B Tank.

Step 15

To secure the S&B support bar to the frame. Slide the u-bolts over the bar and slide as close to the frame as possible. Then install the clips, washers and lock nuts onto the u-bolt. The larger of the 2 clips goes onto the driver side frame.

Step 16

Secure the filler hose back onto the S&B Tank.

Flathead Screwdriver

Step 17

This is what the tank should look like when the fuel tank straps and the support bar are installed.

Final Checklist

This final checklist is very important. #1 Make sure all bolts and nuts are safely fastened and torqued. #2 Ensure there is proper driveshaft clearance. #3 Double check fuel line connections, the electrical connection as well as the vent and fill lines. #4 Lastly, fill the tank full and check for any leaks. If you have any questions, call or text us at 909.675.1313