Cart Total
Cold Air Intakes
Enclosed Airbox
Fully enclosed one piece air box that protects the air filter from dirt and keeps out unwanted engine heat.
Clear Lid
The signature clear lid provides a great finished look.
Large Air Filter
Our intake kits come with a massive air filter in either a cleanable or dry media.
Maximum Airflow
Our intake tubes are designed to minimize restriction for better performance.
Premium Silicone
It won't crack, has exceptional tear strength, and can handle temperatures as high as 400F.
Breathe easy. Your engine and warranty are protected.
Engineered For
Maximum Performance
S&B cold air intakes are engineered to minimize air restriction and increase air flow far better than your stock system. Our intake kits come with a fully enclosed one piece air box that protects the air filter from dirt and keeps out unwanted engine heat. The signature clear lid provides a great look and includes a rubber lid seal to keep out more of that power robbing engine heat.
High Performance
Massive Air Filters
Each intake kit comes with a huge, highly-efficient air filter which results in better performance and better protection for your engine. Available in either a 8-layer cotton cleanable or dry extendable media, the choice is yours. Both offer similar performance, so the decision comes down to would you prefer to throw away the filter or clean it.
High Performance
Massive Air Filters
Each intake kit comes with a huge, highly-efficient air filter which results in better performance and better protection for your engine. Available in either a 8-layer cotton cleanable or dry extendable media, the choice is yours. Both offer similar performance, so the decision comes down to would you prefer to throw away the filter or clean it.
Demand Better
Premium Silicone Components
Silicone is a premium rubber which seals better and lasts longer. The air filter, couplers and tube seals in our intake kits are made from our premium silicone rubber. This means they won't crack, has exceptional tear strength, and can handle temperatures as high as 400F. Also, with a high friction surface and no oily residue, our silicone filters and couplers won’t slide off the tube.
Tested To A
Higher Standard
We test all our intakes to the internationally accepted ISO 5011 Standard when testing for airflow, efficiency and capacity. This is the same protocol used by most of the large automakers.
Airflow testing shows us how we compare to stock and our competitors. The goal is to beat both. We test for efficiency to make sure that your engine is protected from debris while sucking in even more air. Lastly, we monitor the capacity of the filter to see how much dirt it can hold before needing to be serviced. Learn More
Tested To A
Higher Standard
We test all our intakes to the internationally accepted ISO 5011 Standard when testing for airflow, efficiency and capacity. This is the same protocol used by most of the large automakers.
Airflow testing shows us how we compare to stock and our competitors. The goal is to beat both. We test for efficiency to make sure that your engine is protected from debris while sucking in even more air. Lastly, we monitor the capacity of the filter to see how much dirt it can hold before needing to be serviced. Learn More
MAF Sensor
No More Check Engine Lights
S&B devotes a huge amount of resources to engineer our intakes that allow your engine to run properly with stock calibration or enhanced tuning. S&B intake kits are designed to avoid check engine lights with a properly mapped Mass Air Flow Sensor.
Million Mile
Warranty
S&B air filters and intake kits purchased from Authorized Dealers are backed by S&B's Million Mile Limited Warranty when used under the typical driving conditions and on vehicles for which they were designed. If one of our products is not performing properly or is defective, S&B will replace it.
Guaranteed
Upgrades
We don't forget about you after your initial purchase. If we release new intake kit for your vehicle, you can upgrade for as low as $159.
Once a customer, always a customer.
FAQS
Both filters offer similar performance characteristics, so the decision comes down to would you prefer to throw away the filter or clean it. Read more
Installing an S&B Intake Kit or Filter will not void your vehicle's warranty as long as you properly install and maintain your intake/filter.
It is illegal for a dealership to void your warranty based solely on the fact that you have installed an aftermarket product. Your rights are protected by the Consumer Product Warranties Law, often referred to as the Magnuson-Moss Warranty Act.
If a dealer threatens to void your warranty, S&B will step in to assist you. "S&B commits that our customers will not be charged for a repair due to the manufacturer denying their warranty claim because of the presence of an S&B intake kit or OE replacement filter. We warrant that using an S&B intake kit or OE filter will not result in the denial of your vehicle’s warranty." Million Mile Warranty
The simple answer is that it depends on your vehicle. Improving the airflow to your engine has been shown to increase horsepower. That being said, we don't publish horsepower numbers because of the inaccurate and outlandish claims made by many of our competitors. Instead we test to the ISO 5011 Filtration Standard and publish the airflow, efficiency and capacity data for each intake. This is the internationally accepted standard for testing filters and intake systems, so we can hold our competition accountable if they make an incorrect claim. Learn more
Our kits are designed to work with the stock system and you will not receive any CEL’s (check engine lights) during normal operation of the vehicle. Although many customers choose to pair our intake with aftermarket tuners, our kits do not require a tuner nor any special tuning in order to provide a performance increase.
During the installation process we ask that you disconnect the battery because this will prompt your vehicle's computer/sensors to recalibrate and adapt to the new intake and the extra amount of airflow coming through the intake tube. This step is sometimes skipped and since the computer doesn't know there was a change to the air intake, it could potentially throw a CEL, but can be easily corrected by disconnecting the battery.
